Product ID:INTERIOR DECK, GRAY ENAMEL, FORMULA 20L
MSDS Date:03/21/1989
FSC:8010
NIIN:00-285-4870
MSDS Number: BGXTJ

CON-LUX COATINGS, INC.

226 TALMAGDE ROAD
EDISON, NJ 08818-0847
US

Emergency Phone: (206) 287-4000

Info Phone: (206) 287-4000

Cage: 60189

CON-LUX COATINGS INC

847 EDISON, NJ 08818-0847 US

Telephone: 732-287-4000

Cage: 60189

STODDARD SOLVENT

CAS: 8052-41-3

RTECS: WJ8925000

Fraction By Weight: >1%

OSHA PEL 500 PPM

ACGIH TLV: 100 PPM; 9293

MAGNESIUM SILICATE (AS NUISANCE DUST)

CAS: 14807-96-6

Fraction By Weight: >1%

OSHA PEL 20 MPPCF

ACGIH TLV: 2 MG/M3

TITANIUM DIOXIDE

CAS: 13463-67-7

RTECS: XR2275000

Fraction By Weight: 7%

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST; 9293

Routes of Entry: Inhalation:YES Skin:YES Ingestion:NO
Health Hazards Acute and Chronic:IRRITATION OF EYES AND SKIN MAY OCCUR
WITH OVEREXPOSURE. CONTINUED BREATHING OF VAPORS MAY IRRITATE
RESPIRATORY TRACT CAUSING HEADACHE, NAUSEA AND DIZZINESS.REPORTS
HAVE ASSOCIATED REPEATED AND PROLON GED OCCUPATIONAL OVEREXPOSURE
TO SOLVENTS WITH PERMANENT BRAIN AND NERVOUS SYSTEM DAMAGE.
Effects of Overexposure:IRRITATION OF EYES AND SKIN MAY OCCUR WITH
OVEREXPOSURE. CONTINUED BREATHING OF VAPORS MAY IRRITATE
RESPIRATORY TRACT CAUSING HEADACHE, NAUSEA AND DIZZINESS. REPORTS
HAVE ASSOCIATED REPEATED AND PROLO NGED OCCUPATIONAL OVEREXPOSURE
TO SOLVENTS WITH PERMANENT BRAIN AND NERVOUS SYSTEM DAMAGE.

First Aid:INHALATION:REMOVE TO FRESH AIR,RESTORE RESPIRATION IF
NECESSARY.TREAT SYMPTOMATICALLY.EYE:FLUSH IMMED W/COPIOUS
QUANTITIES OF WATER FOR 15 MIN MINIMUM.CONSULT
PHYSICIAN.DERMAL:WASH AREAS W/SOAP AND WA TER.REMOVE CONTAMINATED
CLOTHING.SEE PHYSICIAN IF IRRITATION PERSISTS.INGESTION:DRINK 1-2
GLASS WATER TO DILUTE. DO NOT INDUCE VOMITING. SPONTANEOUS VOMITING
KEEP HEAD AT OR BELOW KNEE LEVEL.

Flash Point Method:TCC
Flash Point:105F/40.6C
Extinguishing Media:FOAM,CO2,DRY CHEMICAL,WATER MIST.
Fire Fighting Procedures:SMOTHER FLAMES WITH ONE OF THE ABOVE
EXTINGUISHING MEDIA. WATER MAY BE USED TO COOL DOWN UNOPENED
CONTAINERS IN VICINITY.
Unusual Fire/Explosion Hazard:CONTAINS FLAMMABLE SOLVENT. DO NOT USE IN
AREAS WHERE SPARKS OR OPEN FLAMES ARE PRESENT.

Spill Release Procedures:ELIMINATE ALL IGNITION SOURCES. WEAR
APPROPRIATE PERSONAL PROTECTION EQUIPMENT AND APPROVED
RESPIR.CONTAIN SPILL W/ABSORBENT MATERIAL & PUT INTO VAPOR TIGHT
CONTAINERS. PREVENT MATERIAL FROM CONTACTS WITH WATER OR SEWERS
LEADING TO SURFACEWATER.

Handling and Storage Precautions:STORE IN AREAS DESIGNED TO COMPLY WITH
ANSI/NFPA 30 FLAMMABLE AND COMBUSTIBLE LIQUIDS CODE.

Respiratory Protection:IN OUTDOOR OR OPEN AREAS, USE APPROVED
RESPIRATOR TO REMOVE SOLID AIRBORNE PARTICLES OF OVERSPRAY DURING
SPRAY APPLICATION. IN RESTRICTED VENTILATION AREAS USE APPROVED
RESPIRATOR DESIGNED TO REMOVE A COMBINATION OF PARTICLES AND
VAPOR.
Ventilation:SUFFICIENT IN VOLUME & PATTERN, SHOULD BE PROVIDED TO KEEP
AIR CONTAMINANT CONCENTRATION BELOW PERMISSIBLE EXPOSURE UNIT
Protective Gloves:IMPERVIOUS REQD FOR LONG,REPEATED EXPOS.
Eye Protection:USE SAFETY EYEWEAR TO PROTECT AGAINST.
Other Protective Equipment:PREVENT PROLONGED SKIN CONTACT WITH
CONTAMINATED CLOTHING.
Work Hygienic Practices:WASH HANDS BEFORE EATING, SMOKING OR USING
WASHROOM.
Supplemental Safety and Health
GROUND CONTAINERS WHEN POURING LIQUIDS AND POWDERS TO AVOID STATIC
CHARGE BUILDUP. DONOT HANDLE UNTIL MANUFACTURERS SAFETY PRECAUTIONS
HAVE BEEN READ AND UNDERSTOOD. PROVIDE ADEQUATE VENTILATION OR RE
SPIRATORY PROTECTION TO REMOVE DECOMPOSITION PRODUCTS DURING
WELDING OR FLAME CUTTING COATED SURFACES.

Boiling Pt:B.P. Text:148-323F
Vapor Density:>AIR
Evaporation Rate & Reference:SLOWER THAN ETHER
Percent Volatiles by Volume:52.32

Stability Indicator/Materials to Avoid:YES
OXIDIZING AGENTS.
Stability Condition to Avoid:EXTREME HEAT, SPARKS OR OPEN FLAMES.
Hazardous Decomposition Products:MAY PRODUCE HAZARDOUS FUMES WHEN
HEATED.

Waste Disposal Methods:DISPOSE OF IN ACCORDANCE WITH FEDERAL,STATE AND
LOCAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.